"""Support for climate control."""
from typing import List

from .device import device
from .exceptions import check_error
from .helpers import calculate_crc16


class hysen(device):
    """Controls a Hysen HVAC."""

    TYPE = "Hysen heating controller"

    # Send a request
    # input_payload should be a bytearray, usually 6 bytes, e.g. bytearray([0x01,0x06,0x00,0x02,0x10,0x00])
    # Returns decrypted payload
    # New behaviour: raises a ValueError if the device response indicates an error or CRC check fails
    # The function prepends length (2 bytes) and appends CRC

    def send_request(self, input_payload: bytes) -> bytes:
        """Send a request to the device."""
        crc = calculate_crc16(input_payload)

        # first byte is length, +2 for CRC16
        request_payload = bytearray([len(input_payload) + 2, 0x00])
        request_payload.extend(input_payload)

        # append CRC
        request_payload.append(crc & 0xFF)
        request_payload.append((crc >> 8) & 0xFF)

        # send to device
        response = self.send_packet(0x6A, request_payload)
        check_error(response[0x22:0x24])
        response_payload = self.decrypt(response[0x38:])

        # experimental check on CRC in response (first 2 bytes are len, and trailing bytes are crc)
        response_payload_len = response_payload[0]
        if response_payload_len + 2 > len(response_payload):
            raise ValueError(
                "hysen_response_error", "first byte of response is not length"
            )
        crc = calculate_crc16(response_payload[2:response_payload_len])
        if (response_payload[response_payload_len] == crc & 0xFF) and (
            response_payload[response_payload_len + 1] == (crc >> 8) & 0xFF
        ):
            return response_payload[2:response_payload_len]
        raise ValueError("hysen_response_error", "CRC check on response failed")

    def get_temp(self) -> int:
        """Return the room temperature in degrees celsius."""
        payload = self.send_request(bytearray([0x01, 0x03, 0x00, 0x00, 0x00, 0x08]))
        return payload[0x05] / 2.0

    def get_external_temp(self) -> int:
        """Return the external temperature in degrees celsius."""
        payload = self.send_request(bytearray([0x01, 0x03, 0x00, 0x00, 0x00, 0x08]))
        return payload[18] / 2.0

    def get_full_status(self) -> dict:
        """Return the state of the device.

        Timer schedule included.
        """
        payload = self.send_request(bytearray([0x01, 0x03, 0x00, 0x00, 0x00, 0x16]))
        data = {}
        data["remote_lock"] = payload[3] & 1
        data["power"] = payload[4] & 1
        data["active"] = (payload[4] >> 4) & 1
        data["temp_manual"] = (payload[4] >> 6) & 1
        data["room_temp"] = (payload[5] & 255) / 2.0
        data["thermostat_temp"] = (payload[6] & 255) / 2.0
        data["auto_mode"] = payload[7] & 15
        data["loop_mode"] = (payload[7] >> 4) & 15
        data["sensor"] = payload[8]
        data["osv"] = payload[9]
        data["dif"] = payload[10]
        data["svh"] = payload[11]
        data["svl"] = payload[12]
        data["room_temp_adj"] = ((payload[13] << 8) + payload[14]) / 2.0
        if data["room_temp_adj"] > 32767:
            data["room_temp_adj"] = 32767 - data["room_temp_adj"]
        data["fre"] = payload[15]
        data["poweron"] = payload[16]
        data["unknown"] = payload[17]
        data["external_temp"] = (payload[18] & 255) / 2.0
        data["hour"] = payload[19]
        data["min"] = payload[20]
        data["sec"] = payload[21]
        data["dayofweek"] = payload[22]

        weekday = []
        for i in range(0, 6):
            weekday.append(
                {
                    "start_hour": payload[2 * i + 23],
                    "start_minute": payload[2 * i + 24],
                    "temp": payload[i + 39] / 2.0,
                }
            )

        data["weekday"] = weekday
        weekend = []
        for i in range(6, 8):
            weekend.append(
                {
                    "start_hour": payload[2 * i + 23],
                    "start_minute": payload[2 * i + 24],
                    "temp": payload[i + 39] / 2.0,
                }
            )

        data["weekend"] = weekend
        return data

    # Change controller mode
    # auto_mode = 1 for auto (scheduled/timed) mode, 0 for manual mode.
    # Manual mode will activate last used temperature.
    # In typical usage call set_temp to activate manual control and set temp.
    # loop_mode refers to index in [ "12345,67", "123456,7", "1234567" ]
    # E.g. loop_mode = 0 ("12345,67") means Saturday and Sunday follow the "weekend" schedule
    # loop_mode = 2 ("1234567") means every day (including Saturday and Sunday) follows the "weekday" schedule
    # The sensor command is currently experimental
    def set_mode(self, auto_mode: int, loop_mode: int, sensor: int = 0) -> None:
        """Set the mode of the device."""
        mode_byte = ((loop_mode + 1) << 4) + auto_mode
        self.send_request(bytearray([0x01, 0x06, 0x00, 0x02, mode_byte, sensor]))

    # Advanced settings
    # Sensor mode (SEN) sensor = 0 for internal sensor, 1 for external sensor,
    # 2 for internal control temperature, external limit temperature. Factory default: 0.
    # Set temperature range for external sensor (OSV) osv = 5..99. Factory default: 42C
    # Deadzone for floor temprature (dIF) dif = 1..9. Factory default: 2C
    # Upper temperature limit for internal sensor (SVH) svh = 5..99. Factory default: 35C
    # Lower temperature limit for internal sensor (SVL) svl = 5..99. Factory default: 5C
    # Actual temperature calibration (AdJ) adj = -0.5. Prescision 0.1C
    # Anti-freezing function (FrE) fre = 0 for anti-freezing function shut down,
    #  1 for anti-freezing function open. Factory default: 0
    # Power on memory (POn) poweron = 0 for power on memory off, 1 for power on memory on. Factory default: 0
    def set_advanced(
        self,
        loop_mode: int,
        sensor: int,
        osv: int,
        dif: int,
        svh: int,
        svl: int,
        adj: float,
        fre: int,
        poweron: int,
    ) -> None:
        """Set advanced options."""
        input_payload = bytearray(
            [
                0x01,
                0x10,
                0x00,
                0x02,
                0x00,
                0x05,
                0x0A,
                loop_mode,
                sensor,
                osv,
                dif,
                svh,
                svl,
                (int(adj * 2) >> 8 & 0xFF),
                (int(adj * 2) & 0xFF),
                fre,
                poweron,
            ]
        )
        self.send_request(input_payload)

    # For backwards compatibility only.  Prefer calling set_mode directly.
    # Note this function invokes loop_mode=0 and sensor=0.
    def switch_to_auto(self) -> None:
        """Switch mode to auto."""
        self.set_mode(auto_mode=1, loop_mode=0)

    def switch_to_manual(self) -> None:
        """Switch mode to manual."""
        self.set_mode(auto_mode=0, loop_mode=0)

    # Set temperature for manual mode (also activates manual mode if currently in automatic)
    def set_temp(self, temp: float) -> None:
        """Set the target temperature."""
        self.send_request(bytearray([0x01, 0x06, 0x00, 0x01, 0x00, int(temp * 2)]))

    # Set device on(1) or off(0), does not deactivate Wifi connectivity.
    # Remote lock disables control by buttons on thermostat.
    def set_power(self, power: int = 1, remote_lock: int = 0) -> None:
        """Set the power state of the device."""
        self.send_request(bytearray([0x01, 0x06, 0x00, 0x00, remote_lock, power]))

    # set time on device
    # n.b. day=1 is Monday, ..., day=7 is Sunday
    def set_time(self, hour: int, minute: int, second: int, day: int) -> None:
        """Set the time."""
        self.send_request(
            bytearray(
                [0x01, 0x10, 0x00, 0x08, 0x00, 0x02, 0x04, hour, minute, second, day]
            )
        )

    # Set timer schedule
    # Format is the same as you get from get_full_status.
    # weekday is a list (ordered) of 6 dicts like:
    # {'start_hour':17, 'start_minute':30, 'temp': 22 }
    # Each one specifies the thermostat temp that will become effective at start_hour:start_minute
    # weekend is similar but only has 2 (e.g. switch on in morning and off in afternoon)
    def set_schedule(self, weekday: List[dict], weekend: List[dict]) -> None:
        """Set timer schedule."""
        # Begin with some magic values ...
        input_payload = bytearray([0x01, 0x10, 0x00, 0x0A, 0x00, 0x0C, 0x18])

        # Now simply append times/temps
        # weekday times
        for i in range(0, 6):
            input_payload.append(weekday[i]["start_hour"])
            input_payload.append(weekday[i]["start_minute"])

        # weekend times
        for i in range(0, 2):
            input_payload.append(weekend[i]["start_hour"])
            input_payload.append(weekend[i]["start_minute"])

        # weekday temperatures
        for i in range(0, 6):
            input_payload.append(int(weekday[i]["temp"] * 2))

        # weekend temperatures
        for i in range(0, 2):
            input_payload.append(int(weekend[i]["temp"] * 2))

        self.send_request(input_payload)